Resetting cisco 2950 switch factory default

#Resetting cisco 2950 switch factory default how to
#Resetting cisco 2950 switch factory default full
#Resetting cisco 2950 switch factory default verification
#Resetting cisco 2950 switch factory default password

Cisco Catalyst 9300, 9200, 3650, 3850, 2960X Switch Password Recovery / Reset Host is not available.

If you have already had a Cisco 2960, then you would try to improve your network performance and manageability.

Change to Global Config mode (#conf t) then type: enable secret newpassword. Those switches are Cisco 2960X and coming with 15. Reboot the router using the вЂreloadвЂ™ command and see that the secret password is changed to the one we configured earlier.Cisco 2960x reset. Router#copy running-config startup-configДЁ. This will merge the new enable password into the existing startup-configuration. In the global configuration mode, configure the configuration register back to default by entering the вЂconfig-register 0x2102вЂ™ router command, so the router will boot normally on the next restart. Router(config)#enable secret cisco12345Д¦. Enter a new enable secret in global configuration mode to overwrite the old one.

#Resetting cisco 2950 switch factory default full

The startup-configuration is still there with the full configuration, including the unknown enable secret, but the router does not use it when it boots. After reboot, it will not ask you the secret password and will proceed to the setup wizard or initial system configuration dialog, as it booted up with a blank configuration.ДҐ. Follow this command, confreg 0x2142, to ignore the startup-configuration and reset or reload the router. Press the break sequence (ctrl-Break) while the router is initializing to break into ROMMON prompt.ДЈ. The following procedure is the steps when we are going to recover the forgotten enable password or enable secret command configured in our Cisco router or switch.Дў.

config-register 0x2142 вЂ“ ignore contents of NVRAM (startup-configuration).

config-register 0x2120 вЂ“ boot into ROM Monitor (ROMMON).

config-register 0x2102 вЂ“ boot normally (default configuration register setting).

The following are the most commonly used configuration register settings: It is mainly used to determine how the router boots, to determine boot options, and to set console speed. Configuration Register is a special 16 bits value that can be configured in Cisco routers. We can use the вЂshow versionвЂ™ command to check the configuration register setting on our device. Router#sh running-configД«efore we proceed with password recovery, we will take a look first at the configuration register.

Verify if the Cisco router is reset to factory default by checking if вЂњhostname Router 1вЂќ is disappeared and changed to default. Reload the Cisco router to complete resetting to the factory defaults, and the startup wizard or initial system configuration dialog will appear. %SYS-7-NV_BLOCK_INIT: Initialized the geometry of nvramДҐ. Router 1#write eraseД®rasing the nvram filesystem will remove all configuration files! Resetting the Cisco router to factory default involves erasing the NVRAM. Router 1#copy running-config startup-configД¤. Save the configuration using the вЂcopy running-config startup-configвЂ™ command. No service timestamps debug datetime msecДЈ.

Verify the configuration by using one of the following commands.

#Resetting cisco 2950 switch factory default verification

In the global configuration mode, create a hostname first on the router as we will use it for verification if the router is already reset into the factory settings. The following procedure is the steps when we are going to factory reset a Cisco router.ДЎ.

#Resetting cisco 2950 switch factory default how to

We will discuss how to restore our Cisco routers and switches to the factory defaults and also how to implement password recovery on them.ДЇactory Reset on Cisco Router or Switch IOS It will make a new and blank startup configuration file, and it will show you the setup wizard for a quick configuration of the router.Д«ut what if we want to retain the existing configuration on the router? Another solution is to perform a password recovery on the router. What if we forget the login credentials of our Cisco routers or switches and we are not able to log in to make changes in configuration? To reset the Cisco router or switch is one of the quickest ways to resolve the issue.